Field services

Services

Millwright work on rotating equipment: install it, repair it, overhaul it, and leave a record. Crews travel from Houston. The plant specification and the OEM manual govern every tolerance.

01

Pumps

API 610 when specified

Crews install, repair, and overhaul centrifugal and vertical pumps, including API 610 process pumps when the project specification calls for that publication. The work runs from a bare baseplate through coupling fit-up and the handoff to alignment.

  • Setting a new or replacement pump and its driver
  • Bearing, seal, wear-ring, and impeller fit-up during a repair or overhaul
  • Coupling hubs, spacer fit, and guard clearance
  • Hold-downs, shims, and soft-foot correction before final alignment
  • As-found and as-left notes for the job file

02

Compressors

API 617 when specified

Field installation, repair, and overhaul for centrifugal, axial, and reciprocating compressors. API 617 is the reference for axial and centrifugal compressors and expander-compressors when your specification requires it. Scope follows the OEM procedure for the machine on the pad.

  • Skid, soleplate, and anchor-bolt setting
  • Case-open support: bearings, seals, and rotor reinstall as the procedure describes
  • Coupling and shaft preparation for alignment
  • Pipe strain flagged on the walk-down for the plant’s piping crew
  • A millwright present at startup when the scope includes it

03

Turbines

API 611 when specified

Installation, field repair, and overhaul of industrial steam turbines, including general-purpose turbines covered by API 611 when that publication is specified. The outage plan and the OEM manual set the sequence.

  • Base and coupling alignment to the driven machine
  • Bearing and case work during an opening
  • Shaft and coupling fit-up
  • Walk-down with your turbine or reliability lead before startup

Controls, governors, and trip systems stay with the group that owns them unless the written scope says otherwise.

04

Gearboxes

Installation, repair, and overhaul of industrial gearboxes on pumps, fans, conveyors, compressors, and mill trains.

  • Base flatness and soft foot before the case is closed
  • Gear mesh, backlash, and contact pattern when the OEM procedure calls for those checks
  • Input and output shaft alignment to the driver and the driven machine
  • Coupling fit and guard clearance

05

Fans and blowers

Installation, repair, and overhaul of process fans, cooling-tower fans, and blowers, plus in-place balancing when the rotor and the access allow a balance shot.

  • Bearing, shaft, and hub work
  • Impeller fit and a visual check for rub conditions at the casing
  • Inlet and discharge fit-up called out for the duct crew when it is outside the millwright scope
  • Field balance with phase readings, written for reliability

06

Laser shaft alignment

API 686 when specified

Precision laser shaft alignment of coupled trains. Soft foot is corrected before the final moves. Thermal growth and other offsets are used when you supply the targets. API 686 is the installation reference when the specification requires it.

  • Motor-to-pump, gearbox, and turbine-driven trains
  • Spacer couplings and close-coupled machines
  • Vertical pumps where the machine design allows a laser setup
  • As-found and as-left readings for the job file

We record what the lasers measured. We do not substitute a house tolerance for the one in your specification.

07

Vibration and balancing

Field vibration measurements for troubleshooting and for follow-up after a repair, and in-place balancing of fans, blowers, and other rotors when a balance shot is possible.

  • Amplitude and frequency compared with how that machine usually runs
  • Phase readings when the work is a balance
  • A short written finding your reliability group can file
  • A next step when the data points away from balance — bearing, alignment, or process — without treating one reading as a full program

08

Setting, leveling, and grouting

API 686 when specified

Equipment setting, leveling, and grouting so alignment has a base it can live on. API 686, the recommended practice for machinery installation and installation design, is the reference when your specification requires it.

  • Anchor bolts, shims, and soleplates
  • Preliminary alignment before grout
  • Epoxy or cementitious grout, as the specification requires
  • Final alignment after the grout has cured to the product requirement

09

Turnarounds and shutdowns

Added millwright crews for planned turnarounds and unplanned shutdowns. You provide an equipment list and a window. We work inside the plant permit system and on the schedule your planners set.

  • Scope review before the outage when you want it
  • Crew size set to the list and the window
  • Shift coverage during the shutdown when the plan calls for it
  • Punch-list turnback as each machine is released

Timing is agreed for that event. This site does not advertise a standing emergency clock.

10

Field machining

On-site machining when a flange, a fit, or a soleplate can be restored in place and the access is safe.

  • Flange facing
  • Boring of bores and housings
  • Milling of pads and soleplates
  • A check against the alignment target so the cut serves the machine

If the damage needs a shop, we say so.

11

Commissioning and walk-downs

Pre-startup checks and a walk-down before operations accepts the machine.

  • Rotation direction, coupling gap, and guard fit
  • Alignment checked against the accepted target
  • Hold-downs, anchor bolts, and grout condition
  • A punch list walked with maintenance or reliability
  • A millwright present for the first run when the scope includes it

12

Preventive and predictive maintenance

Scheduled return visits so alignment and balance do not wait for a failure. The predictive work on this site is alignment re-checks and vibration follow-up. Oil analysis, thermography, and motor electrical testing are not offered here.

  • Alignment re-checks on a route you set
  • Vibration follow-up after a repair
  • Planned bearing, seal, and coupling windows
  • Notes your reliability program can keep

How the API publications are used

  • API 610 Centrifugal pumps for petroleum, petrochemical, and natural gas.
  • API 611 General-purpose steam turbines for petroleum, chemical, and gas industry services.
  • API 617 Axial and centrifugal compressors and expander-compressors.
  • API 686 Machinery installation and installation design.

Work is planned and checked in line with these publications when the project specification calls for them. They do not replace the OEM manual, and naming them is not an API monogram or certification.